Full Description
View Full Description
Lab Gruppen D Series
The Lab Gruppen D series offers total integration of the widest range of digital audio and control protocols, offering powerful and unique benefits and capabilities. Available in two variants, each with three different power models to suit any specific application. The first variation delivers the proven quality of Lake Processing combined with Dante, while the second features the ground breaking collaboration with Biamp Systems for complete integration with their Tesira DSP platform.
The D series is available in 3 different power configurations of 8000 W, 12000 W and 20000 W and also boasts the introduction of Rational Power Management (RPM). This allows for true flexibility of power allocation without any loss of channel count. It is the most efficient use of the amplifiers inventory.
Specifications
- Processing / Network: Tesira® by Biamp / AVB
- Number of channels: 4
- Total burst power all channels (share among channels with RP): 8000 W
Max Output Power All Channels Driven
- 2 Ohms (per channel):2000 W
- 2.67 Ohms (per channel):2000 W
- 4 Ohms (per channel):2000 W
- 8 Ohms (per channel):1500 W
- 16 Ohms (per channel):750 W
- Hi-Z 70V (per channel):2000 W
- Hi-Z 100V (per channel):2000 W
Max Output Power Single Channel (all models)
- 2 ohms:4400 W
- 2.67 ohms:5900 W
- 4 ohms:4600 W
- 8 ohms:2300 W
- 16 ohms:1150 W
- Hi-Z 70 V:3300 W
- Hi-Z 100 V:4700 W
Amplifier Output Modules (All Models, All Channels)
- Peak output voltage:194 V
- Max output current:67 A
- Rational Power Management (RPM): Regardless of model, any channel has potential to deliver the max single channel output power (1 channel on D 80:4, 2 channels on D 120:4)
- Default voltage limitation (can be lifted with RPM configuration):155 V
- Protection features: Current Average Limiter (CAL), Very High Frequency Protection (VHF), Direct Current Protection (DC), Short Circuit Protection, Current-Clip Limiter, Voltage Clip Limiter, Temperature protection
Amplifier Platform
- Inter Sample Voltage Peak Limiter (ISVPL):Configurable Peak voltage threshold and profile
- Amplifier gain:Digital configurable amplifier gain 22-44 dB
- Pilot tone generation and analysis:Yes
- Load impedance analysis:Yes
- Temperature control:Regulated fans and show must go on limitation (ATL, PTL)
Audio Performance (Amplifier Platform with Digital Input)
- THD + N 20 Hz - 20 kHz for 1 W:< 0.05
- THD + N at 1 kHz and 1 dB below clipping:< 0.04
- Dynamic range:> 114 dB
- Channel separation (Crosstalk) at 1 kHz:> 70 dB
- Frequency response (1 W into 8 Ohm, 20 Hz - 20kHz):+/- 0.05 dB
- Internal Sample Rate / Data path:48 kHz / 32 bit floating point
- Product propagation delay (straight path analog server input -> amp):3.857 ms / 185 samples @ 48 kHz
Tesira®
- D Series Tesira system integration:Tesira expander class device with full integration of amplifier configuration and amplifier surveillance
- Device swap:Host name hot swap with full configuration transfer
- Auto power down:Configurable auto power down to ultra low consumption SLEEP state
- Channel processing: Mute, Level, Signal invert
AVB Audio Network
- Dante I/O:4x4
- Sample Rates / Transport:48, 96 kHz / Unicast
- Network latency:Configurable 1 or 2 milliseconds
Optional 4 channels analog inputs (included in the Ta versions)
- Usage:Configurable as Tesira® system inputs or analog failover
- Balanced mic or line level input:+48V phantom power and digitally controlled input gain
- Maximum input and digital reference: +24 dBu
- Sampling rate / resolution:48 kHz / 24 bit
- Input impedance:8 k ohm
- Frequency response (20 Hz - 20 kHz @ 4 dBu):+/- 0.25 dB
- THD+N (20 Hz - 20 kHz @ 0 dB gain +4 dBu in):0.006
- Dynamic range (20 Hz - 20 kHz, 0 dB):> 108 dB
- Cross talk (20 Hz - 20 kHz @ 0 dB gain + 4 dBu in):> 85 dB
Back panel user interface
- Optional analog inputs:4 x Terminal block connectors mic/line level analog input with +,- and ground
- Output connectors:4 x 2 pole Terminal block connectors rated at 1000V/76A (exceeding amplifier capacity) Can take up to 16 mm2 (6 AWG) cables
- Ethernet Ports:1 x RJ45 Tesira® Control, AVB networked Audio
- Serial control port:DB-9 RS232 for power state management
- General purpose I/O:Local GPIO for power state management and amplifier surveillance
- Detachable mains cord:Neutrik PowerCon rated at 250V/32A
Front-panel user interface
- System status indication:3 x 3 colored LED. ALARM, ACTIVITY, STATUS for Tesira® system status and Device STATUS indication
- Channel status indication :3 x 3 colored LED per channel. Status indication separated for channel LOAD, AMP, SIGNAL status
- Mute:Per channel touch button for MUTE control and bicolored LED
- Power:Touch button for ON/SLEEP control and 3 colored LED for power state indication
- Select:Touch button and LED for bidirectional device software select functionality
Mains Power
- Nominal voltage:100-240 Volt AC 50-60 Hz
- Operating voltage:70 - 265 V AC 45-66 Hz
- Mains wall plug:Selectable on order CEE 7/7 "Schuko" 230 V / 16 A, NEMA L5-30 "Twistlock" 125 V / 30 A, NEMA 6-20 250 V / 20 A
Power supply features
- Soft start / Inrush power:Yes/ Max 8 A
- Power factor correction:> 0.98 for mains power > 400W
- Regulated switch mode power supply (R.SMPS):Yes
- Breaker Emulation Limiter (BEL):Configurable current threshold and breaker profile
- BEL max current threshold:15 A
- Power Average Limiter (PAL):Yes
- Under Voltage Limiter (UVL):Yes
- Mains undervoltage and overvoltage protection and mains glitch tolerance:Yes
Dimensions
- Dimensions: W: 483 mm (19"), H: 88 mm (2 U), D: 424 mm (16")
- Overall depth front-rear support: D: 463 mm
Weight
Finish
- Finish: Black painted steel chassis with grey painted steel front with detachable grille
Approvals
- Approvals: CE, ETL(ANSI/UL, CSA), PSE, RCM